Page of 41 Go. Load the media roll onto the hanger from left to right. Improper firmware updating may crash printer firmware. Close the top cover and turn on the printer or press the “FEED” button if the printer is already on. This equipment generates, uses, and can radiate radio frequency energy and, if not. Turn on the printer and wait for 5 or more seconds.
|Date Added:||22 February 2012|
|File Size:||29.22 Mb|
|Operating Systems:||Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X|
|Price:||Free* [*Free Regsitration Required]|
I4 2214 have wrinkle-free design, apply automatically to both Inside wound ribbon and Outside wound ribbon, and feature full support of interfaces – Dual USB hosts, Serial, Ethernet, and Wi-Fi can be expanded to fit in all type of applications.
Click back the middle cover.
Argox OS Plus – Argox – Desktop Label Printers
Click the top plla into place. Even though the “Add Printer Wizard” is from Microsoft, it too easily performs a number of tasks incorrectly when updating existing drivers. Zebra GXt Desktop Printer. Insert the ribbon roll into the supply holder. Peel Off Mode Cutting occurs only when the software is properly set.
Argox OS-214 plus User Manual
This argpx also for: Sato DRe Retail Printer. Miscellaneous If the pus shows “Printer Time out” 1. Take off the top cover of the printer. Replacing the Thermal Print Head 1. Setting Parameters More options To use the cutter or peeler function, enter Accessories More Options and select one of the items. Page 30 FEED button. Zebra SL Barcode Printer. By equipping with new flip-down type cutters, including argox os 214 plus ppla and partial-cut types, I4-series Industrial printer comes with user friendly design that makes your media loading time much easier, be means argox os 214 plus ppla simple media-jam free instructions.
Reattach the print head assembly by securing the 4 screws. Push the print head firmly into the casing and shift it to the left.
Argox OS-214 Plus
Page 26 Create a custom size In the Printers menu: Take off the H. Secure the four screws attaching the cutter. M4L Mobile Thermal Printer. Please refer to Appendix I. If the problem persists, replace the print head.
However, there is no guarantee that the interference will not. Load the media roll onto the hanger from left to right. Be careful not to touch the print head elements. Follow Steps 1 to 8 listed in Standard Mode above. Performing Calibration and Configuration Make sure the media is properly loaded and the top cover of the printer is closed. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Improper firmware updating may crash printer firmware. Configuration This section discusses calibration, printing argox os 214 plus ppla and resetting the printer to factory defaults. To print the manual completely, please, download it. The other end of the parallel interface cable connects to the printer connector at the host computer. Put the print head module down and press down firmly until you hear a snap.
Press and hold the feed button while turning on the power, until argox os 214 plus ppla printing motor is activated.
Be the first to rating. Connect the USB cable, Serial cable to the proper port on the printer and on your computer.
Secure the four screws attaching the cutter. Align the media roll to the left end. Loading a Ribbon Note: Remove the middle cover. Pin 9 are reserved for KDU keyboard device unittherefore do not connect these pins if you are using a general host like a PC.
The O4 series label printer features an easy to use plux design that allows a user to simply argox os 214 plus ppla the cover and load ribbon and labels. Serial rs Interface Requirements Serial RS Interface Requirements The required opla must have a nine-pin “D” type male connector on one end, which is plugged into the mating serial port located on the back of the printer.
Caring For Your Printer Caring for Your Printer Adhesives and coatings of media can over time transfer onto the printer components along the media path including the thermal argox os 214 plus ppla head and media sensor. This section does not arfox to direct thermal printing. This section does not apply to direct thermal printing.
Label Cutting Mode Note: This unit was tested with shielded cables on the peripheral devices. Comments to this Manuals Your Name.